Placas Digitales

>> Digium Wildcard TE411P

The TE411P offers an on-board echo cancellation module. It supports E1, T1, and J1 environments and is selectable on a per-card or per-port basis.

The echo cancellation module supports all T1, E1, and J1 channels and improves voice quality in environments where software echo cancellation is not sufficient. The TE411P reduces CPU overhead required for software echo cancellation thereby, freeing resources for other processes, such as codec translation. By supporting 16ms with 128 channels or 64ms on 32 channels this card will perform in the most difficult of environments.
Digium has designed the TE411P to be fully compatible with existing software applications and it is fully integrated with the Asterisk Open Source PBX/IVR platform. Also, the open source driver supports an API interface for custom application development. With the combination of Digium Hardware and Asterisk software, numerous combinations of telephony configurations are possible. From the traditional PBX to VoIP Gateways, Digium solutions are paving the way for a new generation of worldwide communications.
The TE411P supports industry standard telephony and data protocols, including Primary Rate ISDN (both N. American and Standard Euro) protocol families for voice, PPP, Cisco, HDLC, and Frame Relay data modes. Both line-side and trunk-side interfaces are supported, also included are advanced call features. The TE411P is for use only with a 3.3 volt PCI slot.
The TE411P is certified for Europe, North America, and Australia.

>> Digium Wildcard TE410P

The TE410P is the next generation of Digium hardware that improves performance and scalability through bus mastering architecture.

The TE410P supports E1, T1, and J1 environments and is selectable on a per-card or per-port basis. This feature enables signaling translation between E1, T1, J1 equipment and allows inexpensive T1 channel banks to connect with E1 circuits. Because the TE410P improves I/O speed by up to 10 times, the result is reduced CPU usage and increased card density per server.
Digium has designed the TE410P to be fully compatible with existing software applications and it is fully integrated with the Asterisk Open Source PBX/IVR platform. Also, the open source driver supports an API interface for custom application development. With the combination of Digium Hardware and Asterisk software, numerous combinations of telephony configurations are possible. From the traditional PBX to VoIP Gateways, Digium solutions are paving the way for a new generation of worldwide communications.
The TE410P supports industry standard telephony and data protocols, including Primary Rate ISDN (both N. American and Standard Euro) protocol families for voice, PPP, Cisco, HDLC, and Frame Relay data modes. Both line-side and trunk-side interfaces are supported, also included are advanced call features.
Digium cards are smarter! Second-generation firmware for Digium multispan TE-series hardware PCI cards, provides several new features. These features allow Digium cards to do more work in hardware and leaving the server's CPU open to do other tasks, all of which contribute to less CPU overhead, and therefore improved performance, and more channels running through a single PC or server.

• TDM channel alignment in hardware (instead of software), for greater voice integrity and reliability.
• Master clock source distribution for synchronized timing across multiple cards, assuring synchronization of clocks and increasing reliability and quality of data transmission.
• Zero-latency TDM direct hardware-level cross-connect
• Support for new echo-cancellation module which further increases performance.
• DTMF detection can be done in hardware with echo cancellation module.
• Field upgradable firmware for future updates.

The TE410P supports a 3.3v PCI slot only - typically available on newer motherboards and in 64-bit PCI bus architectures. The TE405P is for use only with a 5.0 volt PCI slot.

>> Digium Wildcard TE406P

The TE406P offers an on-board echo cancellation module. It supports E1, T1, and J1 environments and is selectable on a per-card or per-port basis.

The echo cancellation module supports all T1, E1, and J1 channels and improves voice quality in environments where software echo cancellation is not sufficient. The TE406P reduces CPU overhead required for software echo cancellation thereby, freeing resources for other processes, such as codec translation. By supporting 16ms with 128 channels or 64ms on 32 channels this card will perform in the most difficult of environments.
Digium has designed the TE406P to be fully compatible with existing software applications and it is fully integrated with the Asterisk Open Source PBX/IVR platform. Also, the open source driver supports an API interface for custom application development. With the combination of Digium Hardware and Asterisk software, numerous combinations of telephony configurations are possible. From the traditional PBX to VoIP Gateways, Digium solutions are paving the way for a new generation of worldwide communications.
The TE406P supports industry standard telephony and data protocols, including Primary Rate ISDN (both N. American and Standard Euro) protocol families for voice, PPP, Cisco, HDLC, and Frame Relay data modes. Both line-side and trunk-side interfaces are supported, also included are advanced call features. The TE406P is for use only with a 5.0 volt PCI slot.
The TE406P is certified for Europe and North America.

>> Digium Wildcard TE405P

The TE405P is the next generation of Digium hardware that improves performance and scalability through bus mastering architecture.

The TE405P supports both E1, T1, J1 environments and is selectable on a per-card or per-port basis. This feature enables signaling translation between E1, T1, and J1 equipment and allows inexpensive T1 channel banks to connect with E1 circuits. Because the TE405P improves I/O speed by up to 10 times, the result is reduced CPU usage and increased card density per server.
Digium has designed the TE405P to be fully compatible with existing software applications and it is fully integrated with the Asterisk Open Source PBX/IVR platform. Also, the open source driver supports an API interface for custom application development. With the combination of Digium Hardware and Asterisk software, numerous combinations of telephony configurations are possible. From the traditional PBX to VoIP Gateways, Digium solutions are paving the way for a new generation of worldwide communications.
The TE405P supports industry standard telephony and data protocols, including Primary Rate ISDN (both N. American and Standard Euro) protocol families for voice, PPP, Cisco, HDLC, and Frame Relay data modes. Both line-side and trunk-side interfaces are supported, also included are advanced call features.
The TE405P is for use only with a 5.0 volt PCI slot. The TE410P is for use only with a 3.3 volt PCI slot - typically available on newer motherboards and in 64-bit PCI bus architectures.

>> Digium Wildcard TE210P

The TE210P is the next generation of Digium hardware that improves performance and scalability through bus mastering architecture.

The TE210P supports E1, T1, and J1 environments and is selectable on a per-card or per-port basis. This feature enables signaling translation between E1, T1, J1 equipment and allows inexpensive T1/J1 channel banks to connect with E1 circuits. Because the TE210P improves I/O speed by up to 10 times, the result is reduced CPU usage and increased card density per server.
Digium has designed the TE210P to be fully compatible with existing software applications and it is fully integrated with the Asterisk Open Source PBX/IVR platform. Also, the open source driver supports an API interface for custom application development. With the combination of Digium Hardware and Asterisk software, numerous combinations of telephony configurations are possible. From the traditional PBX to VoIP Gateways, Digium solutions are paving the way for a new generation of worldwide communications.
The TE210P supports industry standard telephony and data protocols, including Primary Rate ISDN (both N. American and Standard Euro) protocol families for voice, PPP, Cisco, HDLC, and Frame Relay data modes. Both line-side and trunk-side interfaces are supported, also included are advanced call features.
The TE210P supports a 3.3v PCI slot only - typically available on newer motherboards and in 64-bit PCI bus architectures. The TE205P is for use only with a 5.0 volt PCI slot.

>> Digium Wildcard TE205P

The TE205P is the next generation of Digium hardware that improves performance and scalability through bus mastering architecture.

The TE205P supports both E1 and T1/J1 environments and is selectable on a per-card or per-port basis. This feature enables signaling translation between E1 and T1/J1 equipment and allows inexpensive T1/J1 channel banks to connect with E1 circuits. Because the TE205P improves I/O speed over slave-only architecture, the result is reduced CPU usage and increased card density per server. Digium has designed the TE205P to be fully compatible with existing software applications and it is fully integrated with the Asterisk Open Source PBX/IVR platform. Also, the open source driver supports an API interface for custom application development. With the combination of Digium Hardware and Asterisk software, numerous combinations of telephony configurations are possible. From the traditional PBX to VoIP Gateways, Digium solutions are paving the way for a new generation of worldwide communications.

>> Digium Wildcard TE110P

The Wildcard TE110P brings a high-performance, cost-effective, and flexible single span togglable T1, E1, J1 interface to the Digium line-up of telephony interface devices.

The TE110P is a single span, selectable T1 (24-channel), E1 (32-channel), or J1 (24-channel) card that supports all the functionality of our quad T1/E1/J1 card. This card supports both voice and data modes on its single span. For example, the card can support 12 channels dedicated to voice and 12 to data while passing all traffic through to the Asterisk Open Source PBX, which reliably routes the channels to their designated locations. This eliminates the need for an external router. The TE110P works in both 3V and 5V slots by autodetecting the slot's voltage.
By utilizing our TDMoE (TDM over Ethernet) technology, an exclusive Digium process, one can easily connect multiple PCs equipped with the TE110P and achieve voice quality on par with single PBX implementations. Scalability for this product is derived from adding multiple TE110Ps to each individual PC. Add addition cards as you need them for your expanding applications.
The TE110P supports industry standard telephony and data protocols, including both RBS and Primary Rate ISDN (PRI) protocol families for voice and PPP, Cisco HDLC, and Frame Relay data modes. The board drives both line-side and trunk-side interfaces, including call features.